Manufacturers Name: Trans Chem Coatings             Date Prepared: 6/15/99

Emergency No.: 1- 800-421-2849                             Information: 626-358-1151

Product Class: Printing Ink

Product Name: Anoprint Dyes

                                                           Section II

                                   INGREDIENTS/ IDENTITY INFORMATION

Propylene Glycol Monomethyl Ether

CAS# 107-98-2

NIOSH (RTECS) UB7700000

OSHA PEL 100 ppm

OSHA/ACGIH STEL: 150 ppm

ACGIH TLV 100 ppm

Percent <40%

                                                        Section III

                           PHYSICAL CHEMICAL CHARACTERISTICS

Physical Form : Liquid, Viscous

Color : Clear (Colors: Black, Red, Yellow, Brown, Blue, Green)

Odor : Mild Solvent

pH : n/a

Boiling Point : 246 deg F

Solubility in Water : Insoluable

Specific Gravity : 1.05

Bulk Density : 8.5 Lbs/Gal

% Volatile by Weight : apx 85%

Vapor Pressure : 8.0 mm Hg at 68 deg F

                                                        Section IV

                                   FIRE & EXPLOSION HAZARD DATA

Flash Point : 91 deg F

Flammable Limits:

Upper Explosive Limit (UEL) (%) : n/k

Lower Explosive Limit (LEL) (%) : 1.5%

Auto-Ignition Temperature : Not established

Extinguishing Media : Dry Chemical; Carbon Dioxide; Form; Water

Special Fire Fighting Procedures : Full emergency equipment with self-contained breathing

apparatus and full protective clothing should be worn by firefighters. During a fire, irritating,

highly toxic gases may be generated by thermal decomposition or combustion.

Unusual Fire / Explosion Hazards : Isolate from heat, electrical equipment, sparks and open flame.

 Closed container may explode when contaminated with water (CO2 evolved). Solvent vapors may

                                                        Section V

                                                REACTIVITY DATA

This product is stable

Conditions to avoid: moisture, excessive heat, sources of ignition

Incompatibility: avoid water, reactive materials

Hazards decomposition products: carbon dioxide/ carbon monoxide

Hazards polymerization: None

                                                        Section VI

                                            HEALTH HAZARD DATA

Acute Hazard: Burning, tearing, drying or cracking of skin, coughing, chest pain, difficulty in

breathing, nausea, vomiting, abdominal discomfort, diarrhea. Medical conditions generally

 aggravated by exposure-any respiratory or skin condition

Possible routes of entry: inhalation, ingestion, skin absorption

Emergency and first aid procedures: Eyes: Flush with water for 15 minutes. Skin: Wash with soap

 and water, not with solvents. Inhalation: Remove to fresh air from exposure area, give CPR

 if necessary. Ingestion: Do not induce vomiting. In all cases, obtain immediate medical attention.

Carcinogenicity: NTP: No IARC: No OSHA: No

HMIS: (mixture) Health: 1 Flammability: 3 Reactivity: 0

                                                        Section VII

                        PRECAUTIONS FOR SAFE HANDLING AND USE

Precautions to be taken in handling storage:

Keep containers closed when not in use. Do not store above (115 deg. F ) keep from freezing.

Empty containers may contain product residue. Do not cut, puncture or weld containers.

All label warning must be observed, until container has been cleaned or reconditioned, or properly

 disposed of. Mix material well to proper specifications.

Spills: Wear air supplied NIOSH approved respirator for major unventilated release.

Cover with absorbent material and keep loosely covered. Clean up residue with solvent.

Section VIII

CONTROL MEASURES

Ventilate area; remove spills with inert absorbent.

Waste disposal method: Dispose in chemical disposal area or in a manner that complies with local state and federal regulations, do not incinerate closed containers.

Use solvent resistant protective gloves, chemical splash safety glasses, and protective solvent resistant apron.

DOT ID#: UN1993

DOT proper shipping name: Printing Ink

DOT Label: Flammable Liquid

DOT Class 3